SLM SERIES 300 W-1200 W HIGH VOLTAGE POWER SUPPLIES

Typical applications:

•      Capacitor charging
•      High potential test
•      CRT testing
•      Electrostatics
•      Electron ray systems
•      CW lasers

Input Voltage:

Power factor corrected input ≥0.98

90-264Vac: 47-63Hz @ 4.0A for 300 watt units

180-264Vac: 47-63Hz @ 4.0A for 600 watt units

47-63Hz @ 8.0A for 1200 watt units

Output Voltage: 

11 models—1kV to 70kV

Output Polarity:

Negative or positive, specify at time of order

Local Indicators:

Arc, HV On, Temp Error, OVP, I Mode 
Power On, OC, Reg Error

Power:

3 power ranges available—300, 600 and 1200 watts. Other power levels available on special order. 

Voltage Regulation:

≤ 0.01% of rated output voltage over specified 
input voltage range 
≤ 0.01% of rated output voltage for a full load change

Current Regulation:

≤ 0.01% of rated output current over specified input voltage range 

≤ 0.01% of rated output current for a ±100µA 
for a full voltage change

Ripple:

≤ 0.2% rms of maximum rated voltage, 
measured with a 10 foot long HV cable

Stability:

≤ 50ppm/hr after a 2 hour warm up

Temperature Coefficient:

≤ 100ppm per degree C 

Environmental:

Temperature Range: 

Operating: 0°C to 40°C 
Storage: -40°C to 85°C

Humidity: 

20% to 85% RH, non-condensing.

Control Interface

Local Interface: 

Potentiometers are provided to adjust voltage and current.

Remote Interface:

USB, Ethernet and RS-232 are standard, implemented with 12 bits of resolution. All digital monitors have an accuracy specification of 2%. 

Control Software:

A Windows graphical user interface example is provided.
embedded applet for control.

HV Control Enable/Interlock:

A dry contact, hardware based interlock is provided for remote mode. In local mode this I/O is the enable. 

Monitor Signals:

Voltage and current monitor signals are scaled 0-10Vdc equals 0-100% of full scale, accuracy is 1%. 

Cooling: 

Forced air 

Dimensions:

300/600 watts: 

4.75˝ H X 6˝ W X 12˝ D (120.65mm x 152.4mm x 304.8mm)

1200 watts: 

4.75˝ H X 12˝ W X 12˝ D (120.65mm x 304.8mm x 304.8mm)

160kV:

10.5˝ H X 19˝ W X 21.5˝ D (266.7mm x 482.6mm x 546.1mm)

Weight:

300/600 watts: 14 pounds (6.35kg) 
1200 watts: 26 pounds (11.8kg)

Input Line Connector:

IEC320 cord set with integrated EMI filter

Output Cable:

A detachable 10’ (3.3m) long shielded HV cable is provided

Regulatory Approvals:

Compliant to 204/108/EC, the EMC Directive and 2006/95/EC, the Low Voltage Directive. UL/CUL recognized, File 227588. RoHS compliant.

FIRMWARE CONFIGURATIONS:

STANDARD BASED FEATURES

AOL - Adjustable Overload Trip 
AT - Arc Trip 
NAD - No Arc Detect 
NSS - No Slow Start 
PSS - Programmable Slow Start 
RFR - Remote Fault Reset 
RMI - Remote Mode Indicators 
ROV - Remote Overvoltage Adjust